Metal fabrication · pricing guide
MS Gate Price in Gurgaon: How It's Calculated
An MS (mild steel) gate is priced mainly by how much steel goes into it, so the section size, the gate's area and the design decide the cost, followed by the finish, the hardware and any motor. FabWise quotes MS gates after a ₹99 site visit, with a written all-inclusive quote within about 2 hours.
The MS gate price in Gurgaon is not a single per-piece figure, because no two gates use the same amount of steel. A main gate for a builder floor in DLF Phase 3, a sliding gate across a villa driveway in Nirvana Country and a safety door for a flat in Gurugram all start from the same material, mild steel, but end up costing very different amounts. This guide explains how the price is built so you can read any quote with confidence.
What unit is an MS gate priced in?
Fabricators commonly use one of two units, and it helps to know which one a quote is using.
| Unit | How it works | Watch for |
|---|---|---|
| Per kg of steel | The gate is designed, its sections are weighed (or calculated), and the weight is multiplied by a rate that covers material and labour. | A low rate per kg on a heavy gate can cost more than a higher rate on a lighter one. Ask for the estimated total weight. |
| Per sq ft of gate | The width × height of the gate is multiplied by a rate for that design. | Two gates of the same size can use very different steel. Ask what sections are assumed. |
| Lump sum | One figure for the finished, fitted gate. | Make sure the finish, hardware and installation are written into it. |
FabWise gives you a written quote for the finished, fitted gate, with the specification listed, so you are comparing the total you will pay rather than a rate that leaves things out.
What drives the cost of an MS gate?
| Cost driver | Why it matters |
|---|---|
| Section size and thickness | Heavier box sections and thicker pipe mean more steel per sq ft. A gate made in lighter sections looks similar on day one but flexes and sags sooner. |
| Gate size | A wider or taller gate needs more steel and stronger hinges or a heavier track. |
| Design complexity | Plain vertical bars are quick to fabricate. CNC-cut sheet patterns, cast motifs and curved tops add machine time and welding. |
| Sheet infill | A gate with full MS sheet for privacy uses far more steel than an open bar design. |
| Finish | Red-oxide primer plus enamel paint is the basic finish. Powder coating lasts longer but is a separate process, usually done off site. |
| Swing or sliding | A sliding gate needs a floor track, wheels and guide rollers; a swing gate needs heavy-duty hinges and a stopper. |
| Motorisation | An automatic opener, its wiring and any remote or sensor are a separate cost from the gate itself. |
| Site work | Pillars that need strengthening, a track that needs a level concrete bed, or a difficult approach all add work. |
How do you read and compare MS gate quotes?
- Get the same specification on every quote: gate size, section sizes, design and finish.
- If a quote is per kg, ask for the estimated weight so you can see the total.
- Check whether primer and paint (or powder coat) are included, and how many coats.
- Check whether hinges, locks, the track and wheels for a sliding gate, and installation are included.
- Ask whether old gate removal and any pillar work are part of the quote.
Red flags in a cheap MS gate quote
- Thin sections. The cheapest way to cut a price is to use lighter steel. The gate may sag and drag within a few monsoons.
- No primer. Paint straight onto bare mild steel lets rust creep underneath. Gurugram's monsoon humidity finds every unprimed joint; see metal gate and grill rusting.
- Unground welds. Rough welds trap water and look poor once painted.
- Light-duty hardware on a heavy gate. Weak hinges or a thin sliding track lead to a sliding gate that sticks.
- A per kg rate with no weight. Without the weight the rate tells you nothing about the total.
MS or stainless steel for a gate?
Mild steel is strong, easy to weld into almost any design, and the usual choice for main gates and sliding gates. It must be protected from rust with primer and paint or a powder coat, and repainted over the years. Stainless steel needs no paint but costs more and is harder to work into ornate designs. For most houses and builder floors in Gurugram, a well-primed MS gate is the practical choice; the main gate design guide goes into styles.
Gates for different homes in Gurugram
A builder floor in a DLF Phase or South City usually has a pair of swing gates between existing pillars, often with a sheet panel for privacy. A villa in a gated colony may need a wide sliding gate because the driveway slopes or space inside is tight. A flat needs an MS safety door in front of the main door rather than a gate. Each uses steel differently, which is why a single rate would mislead.
How FabWise quotes an MS gate
MS gates are quoted after a site visit, because the opening, the pillars, the slope of the driveway and the design all change the steel. The visit costs ₹99 and is adjusted against the bill if you go ahead. We measure the opening, check the pillars and the floor where a track or stopper goes, and talk through design and finish. You then get a written, all-inclusive quote for the agreed scope within about 2 hours, valid for 3 days. Payment is 50% advance to start fabrication and 50% on completion.
See every style in the metal fabrication catalogue, including the MS main gate, MS safety door and MS window grill, or read about metal fabrication in Gurgaon and in Noida.
Send a photo of the opening and a design you like on WhatsApp, then book the visit to get a written figure.
Common questions
How is the price of an MS gate calculated in Gurgaon?
Mostly by the steel in it: the gate's size, the section sizes and the design decide the weight, and the weight drives the cost. Finish, hinges or sliding hardware, motorisation and installation come on top. FabWise gives one written, all-inclusive quote after a ₹99 site visit.
Is an MS gate priced per kg or per sq ft?
Both are common. A per kg rate multiplies the gate's weight; a per sq ft rate multiplies its area for a given design. Either way, ask for the section sizes and the estimated weight, so you can see what you are actually buying and compare the total.
Why are two quotes for the same gate so different?
Usually the steel. A gate built in lighter sections weighs less and costs less, but it flexes and sags sooner. Differences in finish (primer and paint versus powder coat), hardware and whether installation is included also explain the gap. Put every quote on the same specification.
Gate ka rate phone pe mil sakta hai?
Not accurately, because there is no fixed rate for gates: the opening, pillars and design decide the steel. Send a photo on WhatsApp to start the conversation, then a ₹99 visit gets you a written quote within about 2 hours.
Does an MS gate need painting?
Yes. Mild steel rusts if left bare, so it needs a primer such as red oxide and then enamel paint, or a powder coat. A quote that leaves out the primer is cutting a corner that shows up as rust after the first monsoon.
Can you automate an existing gate?
Often, if the gate is straight, swings or slides freely and the pillars are sound. Motorisation is priced separately from the gate. Share a photo and the visit will check whether the gate can take an opener as it is.
Services on this page
More price guides
Book it, or fix it
- MS & SS Metal Fabrication: every style
- MS & SS Metal Fabrication in Gurgaon
- MS & SS Metal Fabrication in Noida
- MS & SS Metal Fabrication in Delhi
- MS & SS Metal Fabrication in Faridabad
- MS & SS Metal Fabrication in Ghaziabad
- MS & SS Metal Fabrication in Greater Noida
- Iron gate or window grill is rusting and the paint is flaking
- Sliding gate is stuck, jerky or hard to push along its track
- Main gate has sagged and drags on the floor when opened