Swing gates · Gurgaon & Noida

Main gate sagging and dragging on the floor in Gurgaon: why and how to fix it

A swing gate drags when it has dropped at the latch end: the hinges or hinge pins have worn, the pillar or wall it hangs on has leaned, or the gate frame itself has bent out of square. Worn hinges are a repair; a leaning pillar or twisted frame needs structural work or a new gate.

Updated 8 October 2026Gurugram & Noida

Double-leaf mild steel main gate hung on masonry pillars

Every swing gate is a lever. Its whole weight hangs off two or three hinges on one side, and the far end, the latch side, is pulled down by gravity every hour of every day. Over years, something gives. The latch end drops, it starts scraping the driveway, the bolt no longer lines up, and eventually the gate needs to be lifted to close. In Gurugram's independent houses and builder floors, where gates are often wide and heavy, this is one of the most common gate problems.

Find which part has moved

Close the gate and look at the gap along the top between the gate and the pillar, and between the two leaves of a double gate. Then look at the hinges while someone lifts the latch end slightly.

If the gate moves up and down at the hinges with play you can see, the hinges or pins are worn.
If the hinges are tight but the whole pillar or post looks out of plumb, the support has leaned.
If the hinges and pillar are fine but the gate's frame is no longer a rectangle (a diagonal is visibly longer), the gate itself has sagged.

The causes, ranked

Worn hinges and hinge pins

Pin hinges on MS gates wear oval with years of swinging, especially without grease and with dust in the joint. A millimetre of wear at the hinge becomes several centimetres of drop at the latch end of a wide gate.

A pillar or post that has leaned

Brick pillars with no steel inside, a steel post set in a shallow footing, or a pillar on ground that has settled after the monsoon all lean slowly toward the weight of the gate. The hinges stay tight but the whole gate tips.

Hinge fixings pulled loose

Hinges fixed with anchor bolts into brick, rather than welded to a plate cast into the pillar, can work loose. You'll see cracks around the fixings or the hinge plate moving.

The gate frame has dropped

A gate made from light section without a diagonal brace, or with heavy infill sheet, slowly racks out of square. Rust at the bottom corners speeds this up.

The floor has risen

Sometimes the gate hasn't moved at all: new tiles, a re-laid driveway or a raised road level has closed the gap underneath.

Gate dragging on the floor: what to check
Check	Points to	Usual fix
Play at the hinges when lifting	Worn hinge pins	Replace hinges, re-hang the gate
Pillar out of plumb	Leaning pillar or post	Rebuild or reinforce the support
Cracks around hinge bolts	Fixings pulled loose	New hinge plates, properly anchored
Frame no longer square	Gate racked or rusted at corners	Add bracing, repair, or a new gate
Gate unchanged, floor higher	New flooring or driveway	Raise the gate or trim the bottom

What you can do safely

Grease the hinge pins if they're greasable, and clear dust from them.
Tighten any loose hinge bolts you can reach, but don't hammer or lever the gate.
Prop the gate open on a block rather than letting it hang, until it's repaired, to take load off the hinges.
Don't try to lift a heavy gate off its hinges yourself.

Repair, or a new gate?

New hinges and re-hanging fix a gate whose frame is still square and whose pillar is sound. Adding a diagonal brace or a wheel under the latch end helps a wide leaf. If the pillar has leaned, it must be fixed first or any new gate will drop again. A new MS main gate makes sense when the frame is rusted at the corners, has racked badly, or you're redoing the entrance anyway; it can be made with heavier hinges, a welded hinge plate and bracing. Where the driveway is short or the gate is very wide, a sliding gate takes the weight off the hinges entirely. See the main gate design guide and the MS gate price guide.

How FabWise handles a sagging gate

On WhatsApp, send a photo of the whole gate closed, close-ups of each hinge, and a short video of the gate opening and closing. If it needs a visit, that's ₹99, adjusted against the bill if you go ahead. Gate work is quoted after the visit; there's no published rate.

Keeping a gate from sagging

Grease the hinges twice a year, before summer and after the monsoon. Don't let children swing on the gate. Keep the bottom corners painted so rust doesn't weaken the frame, as covered in gate and grill rusting. If you have a slider with similar trouble, see sliding gate stuck.

Browse the metal fabrication catalogue, or see metal fabrication in Gurgaon. Send a photo of the hinges on WhatsApp and we'll tell you what's moved.

Common questions

Why is my main gate touching the floor?

The latch end has dropped. Usually the hinges have worn, the pillar has leaned, or the gate frame has sagged out of square. Sometimes the floor has been raised with new tiles or paving. Check for play at the hinges and whether the pillar is upright to find out which.

Can a sagging gate be fixed without replacing it?

Usually yes, if the gate frame is square and not badly rusted. New hinges, re-hanging, a diagonal brace or a support wheel at the latch end fix most sagging gates. If the pillar has leaned, it must be repaired first. A new gate makes sense when the frame itself has racked or rusted through.

Should I add a wheel under my heavy gate?

A support wheel under the latch end of a wide leaf takes load off the hinges and stops dragging, but it needs a smooth, level surface across the whole swing. On rough or sloping driveways it can catch. It's often a good addition when a gate is re-hung.

Gate neeche zameen se ghisat raha hai, kya karein?

Check the hinges first. If there's play when you lift the gate, the hinges are worn and need replacing. If the pillar is tilted, it needs repair. Send a photo of the hinges and the gate closed on WhatsApp and we'll tell you whether it's a hinge job or a bigger fix.