MS Main Gate Fabrication in Gurgaon & Noida

Which MS main gate design suits your house?

Most main gates fall into three layouts. A double-leaf swing gate splits the opening in two, so each leaf is lighter and needs less room to swing. A single-leaf gate suits a narrow pedestrian entrance or a farmhouse side gate. An unequal pair (one wide leaf for the car, one narrow leaf for people) is common on builder floors where the family walks in far more often than the car drives in. A small wicket door cut into one leaf does the same job on a single wide gate.

The infill sets the look and the privacy. Full MS sheet gives complete privacy and a solid, modern face. Vertical flat bars or square pipes keep the view out to the street. Laser-cut or CNC-cut panels carry a jaali, geometric or floral pattern and are the most-asked-for style on new villas. Many gates mix them: sheet at the bottom where scooters and dogs push against it, a cut pattern above.

If the drive is short or slopes up towards the house, a swing gate may not clear the ground. That is where a sliding gate on a track does better. Our main gate design guide walks through the options with drawings.

Gates for Gurugram builder floors, villas and farmhouses

Gurugram plots throw up their own gate problems. In the older DLF Phases and Sushant Lok, many houses have been rebuilt as four-storey builder floors, and the gate now serves four families and their cars. These gates get opened forty times a day, so the hinge detail matters more than the pattern. In South City and Nirvana Country the plots are wider and owners often want a matching pedestrian gate beside the car gate.

Farmhouses on the Sohna and Faridabad side want tall, wide gates that are heavy by design. These usually swing on bearing pivots at the bottom rather than hinges alone, because a long leaf drags on its hinges within a monsoon or two.

In Noida sector houses the boundary walls are typically lower and the gate is part of a matching set with the MS boundary railing above the wall. We design both together so the bars line up.

See what else we fabricate on the metal fabrication catalogue, or the metal fabrication page for Gurgaon.

What decides the price of a main gate

MS gates are not sold from a rate list, because two gates for the same opening can differ several times over in steel weight and labour. The quote is worked out after the site visit, and the MS gate price guide explains the method in more depth.

Size and section come first. A wider, taller opening needs heavier box section to stay straight, and steel is bought by weight. Infill comes next: plain vertical bars use the least steel, full sheet uses more, and laser-cut panels add machine time on top of the steel.

The hanging detail matters more than most people expect. Heavy-duty hinges, bottom bearing pivots and hinge plates anchored into the pillar each change both the cost and the life of the gate. Finish is the other big choice: primer and enamel paint costs least, while powder coating costs more but holds its colour and resists chipping far longer.

Then there is the site. If the pillars are hollow brick or cracked, they may need an embedded plate or a steel post before they can carry the gate. Finally the extras: locks, tower bolts, a letter box, a name plate or a wicket door. The written quote lists each of these separately, so nothing is added later.

How the gate job runs with FabWise

Book a visit. It costs ₹99, paid upfront and adjusted against the final bill, and is usually arranged within 24 to 48 hours of booking.

Measure. The team measures the clear opening at the top and at the bottom (they are rarely the same), checks both pillars for plumb and strength, and notes the slope of the drive so the leaves will clear it when they swing.

Design and quote. You settle the pattern, the finish and the hardware with the team. The written, all-inclusive quote usually follows within about two hours of the visit and stays valid for three days.

Advance and fabrication. Work starts after a 50% advance. The frame is cut, welded, ground smooth and finished in the workshop, where primer, paint and powder coat take far better than they do out on a dusty street.

Installation. The gate is brought to site, the hinge plates are fixed into the pillars, the leaves are levelled and aligned, and the locks and stoppers are set.

Balance. The remaining 50% is paid on completion, once the gate swings freely and locks properly.

Keeping an MS gate free of rust

Mild steel rusts wherever bare metal meets water, and Gurgaon's monsoon finds every scratch. The weak points are always the same: the bottom rail where rainwater sits, welded joints, and the spot where the latch rubs. A good gate is made with closed box sections or drain holes so water cannot collect inside.

A painted gate usually needs a fresh coat every two to three years, and a quick touch-up of chips before each monsoon. A powder-coated gate goes much longer between attentions, though a deep scratch should still be sealed before it creeps under the coat. Oil the hinges or pivots every few months; a dry hinge is the most common cause of a gate sagging and dragging on the floor.

If an existing gate is already flaking, read why metal gates and grills rust before deciding between repainting and replacing it.